Door Cost in India 2026: Price by Type, Material & All-In Budget

Ask three vendors what a door costs and you will get three very different numbers — because most of them are quoting only the shutter (the leaf) and quietly leaving out the frame, the hardware, the carpentry and the GST. A door is never a single line item; it is a small kit. The honest answer to "what does a door cost in India" in 2026 is a range that depends on six or seven things, and this guide gives you those ranges, the all-in maths, and two fully worked budgets so you can size your own door bill before anyone hands you a quote.

All figures below are indicative 2026 benchmarks and vary by city, vendor, brand and timber rates. Treat them as a sanity-check band, not a fixed rate card. For a live estimate tuned to your sizes and city, use the door cost calculator; to weigh material trade-offs before you price them, the door material comparison tool is the faster start.

The five things you are actually paying for

Every installed door is the sum of five buckets. Skip any one of them and your budget will be wrong:

1. The shutter (leaf) — the door panel itself. Priced per piece or per square foot of shutter area.

2. The frame (chowkat / chaukhat) — the timber or WPC/steel surround fixed into the wall. Priced per running foot.

3. The hardware — hinges, handle/knob, mortise lock or latch, tower bolt, door stopper, and for main doors a night latch or smart lock.

4. Fitting / installation labour — the carpenter's charge to hang, align, plane and finish the door.

5. Finishing + GST — polish/paint/lamination if not factory-done, plus 18% GST on most factory doors and branded hardware.

A useful rule of thumb: the shutter is rarely more than 45-60% of the installed cost. The frame, hardware and fitting routinely add 40-55% on top. People who budget only the shutter price are short by roughly half.

All-in door cost = Shutter (45-60%) + Frame (10-20%) + Hardware (10-25%) + Fitting (8-15%) + GST (on taxable items)

Cost by door type (shutter only, 2026)

This first table is the shutter only — the leaf, before frame, hardware and fitting. A "standard shutter" here means roughly a 3' × 7' (≈21 sq ft) internal door unless noted.

Notes that change these numbers: WPC and uPVC are sold by opening or shutter area and are the safe budget choice for wet and coastal zones because they do not swell or rot in the monsoon. Teak is the wide outlier — the gap between a plain teak plank door and a hand-carved Rajasthani or South-Indian main door is enormous, which is why teak gets its own deep-dive in our teak door cost guide. For the full money story on the front door specifically, see the main door cost guide.

Cost by material (the durability-per-rupee view)

Type tells you the construction; material tells you how it ages in Indian conditions. The cheapest shutter is not the cheapest over ten years once you factor swelling, termites and refinishing. This is the lens our door materials comparison uses in detail.

A monsoon-and-termite reality check: in coastal Kerala, Goa, Mumbai and the Konkan, a ₹3,000 WPC bathroom door will routinely outlast a ₹6,000 ply door that warps and delaminates within a few seasons. Match material to climate first, then optimise price — that decision logic is the whole point of the best door material guide.

The add-ons: frame, hardware, fitting

Here is where the "shutter price" doubles into an installed price. These are per-door add-ons in 2026.

A standard 3' × 7' door needs roughly a 17-foot frame run (two jambs of ~7 ft plus a 3 ft head). That is why a "₹400/ft teak frame" quietly becomes a ₹7,000 line item on its own. Brands worth knowing for locks and fittings include Godrej, Yale, Hafele, Qubo and Lavna for smart locks; for the full hardware breakdown see the door hardware section of our home doors complete guide.

The all-in cost: putting it together per door

Now the number that matters — the installed, taxed, finished cost of one door, by room.

Two patterns fall out of this. First, the main door alone is often 30-45% of a whole-home door budget — it carries the most material, the heaviest hardware and (usually) the most decoration. Second, bathroom doors should never be your saving target in a wet climate; the WPC premium over ply is small and the failure cost is high.

Where the rupees go — a single door, broken down

Worked example 1: a 2BHK door set

A typical 2BHK has 6-7 doors: 1 main, 2 bedrooms, 2 bathrooms, 1 kitchen, and often 1 balcony/utility. Here is a realistic value budget that does not cut corners where climate punishes you.

Trade up the main door to mid teak and add a smart lock and the same 2BHK lands around ₹85,000-1,10,000. Trade everything down to bare carpenter-made ply and you can reach ~₹40,000 — but expect monsoon swelling on the wet-area doors within a couple of years.

Worked example 2: a 3BHK door set

A 3BHK typically runs 9-11 doors: 1 main, 3 bedrooms, 3 bathrooms, 1 kitchen, 1 pooja, and 1-2 balcony/utility.

A premium 3BHK with a heavily carved teak main door, designer veneers and premium smart locks comfortably crosses ₹2,00,000-3,00,000+. A strict value 3BHK (solid main, engineered internals, WPC wet areas, no smart lock) sits around ₹85,000-95,000.

Hidden costs people forget

The quote you sign is rarely the cheque you write. Watch for these:

• GST (18%) on factory doors and branded hardware — often quoted "extra". On a ₹1.3 lakh door set that is ~₹20,000 you did not plan for.
• Frame is separate. Many vendors quote "₹3,500 door" meaning shutter only. Always ask: shutter, frame or both?
• Finishing. Melamine/PU polish, lamination or paint can add ₹500-8,000 per door if the door arrives unfinished.
• Cutting / resizing non-standard openings, and wall repair around old frames being replaced.
• Hinge and lock upgrades. The "free" hardware is often the cheapest grade; a decent mortise lock and SS hinges are a fair upgrade.
• Transport and lift charges for heavy solid/teak doors, especially to upper floors.
• Two trips of labour — one to fix the frame at masonry stage, one to hang the shutter after painting.

What actually drives the price

Seven levers, roughly in order of impact:

1. Material — teak vs WPC vs ply can swing one door 10×.

2. Solid vs hollow/cellular core — solid costs more, sounds and feels better; see solid vs hollow core doors.

3. Size — main and double doors carry far more material per leaf.

4. Carving / design — plain vs carved teak is the single biggest main-door variable.

5. Hardware grade — a ₹1,500 lock set vs a ₹25,000 smart lock.

6. Carpenter (site-made) vs factory-made (IS 2202) — factory gives consistency and warranty; site-made gives custom sizes and sometimes lower cost.

7. City and timber rates — metros and coastal teak markets run higher; tier-2 towns often cheaper for labour.

A practical sequencing tip: decide material and type per room first (use the door material comparison), then price it — pricing before you have chosen a material just produces apples-to-oranges quotes you cannot compare.

Frequently asked questions

How much does one door cost installed in India in 2026?

An internal bedroom or kitchen door lands at roughly ₹4,500-8,000 all-in (shutter + frame + hardware + fitting + GST). A WPC bathroom door is about ₹3,500-6,000. A main entrance door ranges hugely — from ₹25,000 for a solid-wood door with a decent lock to ₹1,50,000+ for a carved teak door with a premium smart lock.

What is the cheapest door material in India that still lasts?

For wet and coastal areas, WPC at ₹2,000-4,500 a shutter is the best durability-per-rupee — waterproof and termite-proof, so it beats cheap plywood that swells in the monsoon. For dry internal rooms, a factory engineered/HDF flush door (IS 2202) from ₹1,200-4,000 is the value pick.

How much should I budget for all the doors in a 2BHK or 3BHK?

A sensible 2BHK door set runs about ₹55,000-1,10,000 all-in depending on the main door; a 3BHK runs about ₹85,000-2,00,000+. The single biggest swing in both is the main door and whether you add a smart lock.

Why is the vendor's quote so much lower than these numbers?

Almost always because the quote is shutter only — no frame (chowkat), no hardware, no fitting labour, and GST shown "extra". Ask every vendor to itemise shutter, frame, hardware, fitting and GST on one sheet so you are comparing like with like. Our door buying guide has a line-by-line quote checklist.

Is a factory-made door cheaper than a carpenter-made one?

Not always cheaper, but usually better value. Factory doors (IS 2202) give consistent quality, a warranty and predictable pricing; a site carpenter can match odd opening sizes and sometimes undercut on labour but the finish and core quality vary. For standard sizes, factory wins; for non-standard or heritage work, a skilled carpenter still earns their fee.